臺灣標準電機SEW儀器儀表--183 CB Cable Tracer
    <small id="mhuiw"><tbody id="mhuiw"></tbody></small>

            
         
        183 CB   Cable Tracer
        183 CB
        FEATURES
         
         AMPLIFIER PROBE (183 CB-A)
         The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation.
         Works with any Tone Genertor to identify wires.
         Volume control for increased sensitivity and adjustable to suit various work environments.
         Recessed ON/OFF button prevents battery drain.
         Power supply is in any 9V battery with a life of approximately 100 hours.
         A phone jack is designed for headset or handset.
         PHONE TESTER / GENERATOR (183 CB-TFG)
         Phone Tester / Generator is a great tool fo locating and identifying cable pairs or individual conductors.
         183CB-TFG does not only provide the function of a tone generator, but also serves as a condinuity and polarity tester.
         A tone selector switch located inside the unit for selection of the fast tone or slow tone.
         Two bi-colored LEDs for Line 1 and Line 2 indication of the polarities of the telephone lines.
         The unit has alligator-type terminals and a modular cable of 4 conductors with a strong Connector.
         The tone and continuity functions are only applied to Line 1. (modular connector)
         THE FUNCTINOS OF PHONE TESTER :
         Continuity and resistance testing of voltage free jbjects.
         Check direct and alternating voltages.
         Testing capacitors.
         Testing diodes.
         Testing gtransistors.
         Power ON/OFF switch for Test-Phone functions.
         The indication of the LED lamp and buzzer sound occur at the same time.
         The LED indication of Power ON status.
        SPECIFICATIONS
         
        Amplifier Probe (183CB-A) Frequency Detection : 1Hz ~ 12kHz
        Receiver Distance Sensitivity Control : < 50 cm
        Tone Generator (183 CB-TFG) Waveform : Square Wave
        Frequency : 1k Hz +/- 15%
        Over Voltage Protection : 80V DC
        Alternating Tone : Fast and slow
        Connection : RJ11 connector
        Phone Tester (183CB-TFG) U test : < 4.75V
        I test : < 2mA
        Resistance : 0 ~ 2 M
        GENERAL
        Operating Temperature & Humidity 0 degree C ~ 40 degreee C, 80% Max.
        Storage Temperature & Humidity -10 degree C ~ 50 degree C, 80% Max.
        Power Source Amplifier Probe : 9V battery.
        Phone Tester / Generator : 1.5V AA battery x 6
        Dimensions Amplifier Probe : 270 (L) x 50 (W) x 25 (H) mm
        Phone Tester / Generator : 143 (L) x 74.5 (W) x 33.6 (H) mm
        Weight Amplifier Probe : 125g (battery included)
        Amplifier Probe : g (battery included)
        Safety Standard , , ,
        Accessories Instruction Manual
        Batteries
        Carry pouch
        特 點
        音頻接收器(183 CB-A)
         1.具可調式音量控制鈕，依工作環境需要，選擇聲音大小。
        2.外端接點，可與電話筒連接，方便接線人員操作。
        3.使用之操作開關，利於節省電力，延長電池壽命。
        4.連線操作，電池使用壽命約100小時。

        音頻發射器(183 CB-TFG)
        ● 搭配音頻接收器(183 CB-A)，可以分辦或追蹤纜線 或集團線中之一條，而不需要破壞線的外層絕緣體。
        ● 有導通測試和分辨電話線極性的功能。
        ● 機殼內有音頻選擇推鈕，可視工作環境實際需要作音頻快速或緩慢的選擇。
        ● 有兩顆雙色LED，可以偵測Line 1和Line 2的電話 線極性。
        ● 設計有鱷魚夾和RJ11四芯的接頭。
        ● 導通測試只限Line1 LED來判別。
        規 格
        音頻產收器(183 CB-A)
        音頻接收器 1Hz~12kHz
        感應接收距離 < 50cm
        感度控制旋鈕 ˇ
        感應端子 固定式
        使用電池 9V(6F22) × 1
        外形尺寸 230(長)×56(寬)×27(高)mm
        重量(含電池) 約125公克
        音頻發射器與電話系統檢測計(183 CB-TFG)二合一
        波形 方波
        頻率 1kHz±15%
        過載保護 80V DC
        過載保護 快速與緩慢
        電話接頭 RJ11
        使用電池 1.5V (AA) × 6
        外形尺寸 143(長)×74.5(寬)×33.6(高)mm
        重量(含電池) 約318公克
        電話系統檢測計
        較響亮的喇叭 ˇ
        導通測試 ˇ
        檢查額定電阻 ˇ
        檢查額定電壓(AC/DC) ˇ
        檢查額定電容 ˇ
        檢查額定二極體 ˇ
        一般敘述
        操作溫濕度 0°C-40°C Z大相對濕度80%
        儲存溫濕度 -10~50C, Z大相對濕度80%
        安規條款