 |
| |
286 SVD High Voltage Testers
Personal Safety Voltage Detector
|
 |
|
|
FEATURES |
| |
 Non-contact voltage detection 110V~11.4KV. |
| Compact, easy to wear and convenient in use. |
| Usable both indoor and outdoor. |
| Water-proof design. |
| Equipped with self-testing functions. |
| Sound and flash light warning of different frequencies varied positively with sensed voltages. |
| Able to sense all kinds of AC High Voltage System. |
| Low power consumption. |
| |
|
| The 286 SVD is a sensor for sensing AC High Voltage(110V~11.4KV). It provides electric engineering personnel, power engineering personnel, firefighting personnel and instrument equipment workers with prominent warning when approaching high voltage and for taking necessary safety action, preventing illusion and misjudgment which could lead to electric shock. |
| When a person wearing the 286 SVD is approaching a high voltage source or equipment, the sensor will detect automatically, the buzzer will generate a beeping warning sound, and the LED light will flash to remind operator that the user is approaching a high voltage source and special attention shall be given to the safety of operations. |
| METHOD OF USE |
| Inspection before use : |
| (1) Check the appearance and structure for any abnormality. |
| (2) Press Self-Test switch (about 10 seconds) to confirm all functions are working normally. |
| (3) To be careful and to avoid misjudgment, test the unit by contacting AC 110V insulated wire with its front side to see if it sounds and flashes. |
| Wearing : |
| Wear the unit to the outer side of fore arm with the sensing side faces outwardly. The effect is best when the sensing side is facing high voltage in right angle (90 degree). When it is worn at the inner side of arm or is covered by cloth, the sensitivity is poorer. |
|
| SPECIFICATIONS |
| |
| Voltage |
Detection distance |
| 110V |
2cm +/- 0.3cm |
| 600V |
6.7cm +/- 0.5cm |
| 1KV |
11.5cm +/- 1.0cm |
| 2KV |
22.5cm +/- 1.0cm |
| 6KV |
57cm +/- 1.5cm |
| 8KV |
71.5cm +/- 2.5cm |
| 11.4KV |
84cm +/- 3.0cm |
| |
|
| Applicable Frequency |
50/60 Hz |
| Volume |
70 dB or higher at 1 meter distance |
| Operating Temp. & Humidity |
5 degree C ~ 45 degree C / 80%RH |
| Outside Dimensions |
59(L) x 56(W) x 18(H) mm |
| Weight |
35g (battery included) |
| Battery Type |
CR2032 |
| Battery Life |
50 hours for continuous use |
| Accessories |
Elastic cord, Band, Bracket, Instruction manual and Battery |
|
| 特 點 |
● 286 SVD是感知交流高電壓的一種感知器，它提供給電機工程人員、電力工程人員、消防人員及
儀器設備工作人員，在接近高電壓，獲得明顯的警示，進而採取必要的安全行動，防止錯覺、
誤認而發生人員感電事故。
● 配戴286 SVD，在接近高電壓時，感知器即自動偵測。感知結果，蜂鳴器發出嗶-嗶-嗶-短促聲音，
同時LED也產生亮光閃滅，提醒作業人員己接近高電壓，採取必要的安全措施。
● 體積小，配戴容易，方便使用。
● 室外室內均可使用。.
● 作防水設計。
● 具有自我測試功能。
● 聲音和閃亮隨電壓高低感知狀況作不同頻率的警示。
●可感知各種交流高電壓系統。
● 耗電量低。
●
|
注意事項
1. 本感知器僅供輔助驗電器使用，旨在工程作業人員獲得警示，多一重保障。不可以感知器
代替驗電器，仍應以驗電器作為主要的測電儀.感知警示距離，除了配戴方式會影響外，帶
電體的方向，周圍環境狀況，遮蔽物及天候狀況，也會影響感知距離。
2. 蜂鳴器內有防水膜，不可用尖狀物刺破。
3. 不宜長期置於屋外或汽車內，避免曝曬和高溫。
4. 感知器不可重摔或強力碰撞。若不意摔碰，應先檢視和自我測試確定無虞後再使用。
5. 不慎被雨水淋濕時，先取出電池後置於陰涼處所自然乾燥。
6. 儲存時，應將感知器放入防靜電袋，以保持乾燥，防止磁場干擾。 |
|
| 規 格 |
|
| 開始警示距離 |
11.4kV(對地電壓6.6kV)-80公分 |
| 適用頻率 |
50 / 60 Hz |
| 音量 |
距離1公尺 > 70 dB |
| 操作溫濕度 |
0°C~40°C 80% R.H. |
| 電池壽命 |
連續使用，約50小時 |
| 外形尺寸 |
59(長) x 56(寬) x 18(高)mm |
| 重量 |
約35公克(含電池) |
| 使用電池 |
DC3V(CR2032)電池一個 |
|
|
|
